nouvelles
Building a 120V AC to 3V DC Power Supply
Auteur： Module d'alimentation ZYG Time： 2023-4-18
Introduction:
A power supply is an essential component in any electrical or electronic system. It provides the necessary power for the system to operate. In this article, we will discuss how to build a 120V AC to 3V DC power supply. The power supply can be used for a variety of applications such as powering low voltage circuits, charging batteries, and powering small electronic devices.
Design:
The power supply is designed to convert the 120V AC voltage from the mains into a 3V DC voltage. The power supply consists of a transformer, a bridge rectifier, and a voltage regulator.
Transformer:
The transformer is used to step down the 120V AC voltage to a lower voltage suitable for the power supply. The transformer used in this design has a primary winding of 120V AC and a secondary winding of 6V AC. The secondary winding is center-tapped, which means that it has a common ground reference.
Bridge Rectifier:
The bridge rectifier is used to convert the AC voltage from the transformer into a DC voltage. The bridge rectifier is made up of four diodes that are arranged in a bridge configuration. The output of the bridge rectifier is a pulsating DC voltage that has a voltage of approximately 9V DC.
Voltage Regulator:
The voltage regulator is used to regulate the output voltage of the power supply. In this design, a LM317 voltage regulator is used. The LM317 voltage regulator is a three-terminal adjustable voltage regulator that can provide an output voltage between 1.25V and 37V. The LM317 voltage regulator is connected in a voltage divider configuration to provide a 3V DC output voltage.
Circuit Diagram:
The following circuit diagram shows the 120V AC to 3V DC power supply:
[Insert Circuit Diagram Here]
Construction:
The 120V AC to 3V DC power supply can be easily constructed on a breadboard or a PCB. The components required for the power supply are:
1. Transformer: 120V AC to 6V AC center-tapped transformer
2. Bridge Rectifier: 4x 1N4007 diodes
3. Voltage Regulator: LM317
4. Capacitors: 1x 2200uF electrolytic capacitor, 1x 0.1uF ceramic capacitor
5. Resistors: 2x 220 ohm resistors, 1x 240 ohm resistor
6. LED: 1x LED (optional)
The following steps can be followed to construct the power supply:
1. Mount the components on a breadboard or a PCB as shown in the circuit diagram.
2. Connect the 120V AC input to the primary winding of the transformer.
3. Connect the center-tap of the secondary winding of the transformer to the ground.
4. Connect the output of the bridge rectifier to the input of the LM317 voltage regulator.
5. Connect the output of the LM317 voltage regulator to the output terminals.
6. Connect the LED (optional) to the output terminals through a current-limiting resistor.
Testing:
The power supply can be tested by measuring the output voltage using a multimeter. The output voltage should be approximately 3V DC. The LED (optional) can also be connected to the output terminals to test the power supply.
Conclusion:
In this article, we have discussed how to build a 120V AC to 3V DC power supply. The power supply is designed using a transformer, a bridge rectifier, and a voltage regulator. The power supply can be used for a variety of applications such as powering low voltage circuits, charging batteries, and powering small electronic devices. The power supply is easy to construct and can be tested using a multimeter.
Précédent: Convertisseur AC-DC : Conversion du courant alternatif en courant continu
Prochain: Comment câbler une alimentation AC à DC
les informations pertinentes
-
2024-5-30
Power modules: Provide reliable power for your devices
With the continuous advancement of science and technology, electronic devices have become an indispensable part of our daily lives and work. Whether it is smart home appliances, precision instruments in the enterprise, or even large equipment in industrial automation production lines, they all need a reliable power source to ensure their normal operation. The power module is the key component of this power source. 1. The power core of the equipment As the power conversion and supply unit in electronic equipment, its importance is obvious. It can convert the input power into the stable voltage and current required by the equipment, ensuring that the equipment can obtain continuous and stable power supply in various complex environments. 2. Features and Advantages...
Voir les détails -
2023-5-26
Efficient and Reliable ACDC Power Supply SF Series (3~100W)
The SF Series of ACDC power supplies is an efficient and reliable option for powering a variety of electronic devices. With a range of power outputs from 3W to 100W, these power supplies are suitable for a wide range of applications. One of the key features of the SF Series is its high efficiency. These power supplies have an efficiency rating of up to 90%, which means that they waste less energy and generate less heat than less efficient models. This not only helps to reduce energy costs, but also increases the lifespan of the power supply by reducing the stress on its components. The SF Series is also highly reliable, with a long service life and a low failure...
Voir les détails -
2023-7-11
Bidirectional DC-DC Converter: The Future of Efficient Energy Conversion
In today's world, the demand for efficient energy conversion is increasing rapidly due to the growing need for renewable energy sources and the rising concerns about climate change. One technology that shows great promise in meeting this demand is the bidirectional DC-DC converter. The bidirectional DC-DC converter is a device that allows energy to flow in both directions, converting direct current (DC) from one voltage level to another. This converter plays a crucial role in various applications, such as electric vehicles, renewable energy systems, and energy storage systems. One of the key advantages of the bidirectional DC-DC converter is its high efficiency. Traditional converters often suffer from significant energy losses during the conversion process. In contrast, bidirectional converters can achieve...
Voir les détails -
2023-11-3
High Voltage Power Supply Module: Empowering Electrical Systems with Elevated Energy Levels
Introduction: In today's technologically advanced world, the demand for high voltage power supply modules has been increasing exponentially. These modules play a critical role in various industries, providing the necessary power to drive electrical systems with elevated energy levels. This article aims to explore the importance of high voltage power supply modules and their impact on empowering electrical systems. Understanding High Voltage Power Supply Modules: High voltage power supply modules are sophisticated electronic devices designed to convert and amplify voltage levels to meet the requirements of specific electrical systems. Their primary function is to take input voltage from a source and supply high voltage output to power various devices. These modules are commonly used in industries such as telecommunication, medical...
Voir les détails -
2023-5-29
Car AC-DC Converter: Power Up Your Electronics on the Road
Are you tired of running out of battery on your electronic devices while on the road? Do you wish you could charge your laptop, phone, or tablet in your car? Well, now you can with a car AC-DC converter. A car AC-DC converter is a device that allows you to convert the DC power from your car\'s battery to AC power, which can be used to charge your electronic devices. This is especially useful for long road trips or when you need to work on your laptop while on the go. One of the biggest advantages of using a car AC-DC converter is that it is a portable power source. You don\'t need to worry about finding a power outlet...
Voir les détails -
2023-5-31
SP Series AC DC Converter: Efficient and Reliable Power Conversion Solution
As technology advances, the need for efficient and reliable power conversion solutions for various applications has become increasingly important. One such solution is the SP series AC DC converter, which offers excellent performance and reliability for a wide range of industrial and commercial applications. The SP series AC DC converter is designed to convert a high voltage alternating current (AC) power source into a low voltage direct current (DC) output. This conversion is essential for powering electronic devices and systems that require stable and reliable DC power. The SP series converter is highly efficient, typically converting 85-90% of the input power into usable DC power, which helps to reduce energy consumption and operating costs. One of the key features of...
Voir les détails