Вести
Воведување на Кина производители на моќни модули со мала големина
Автор: ZYG Power Module Time： 2022-5-5
When we choose a power module, we generally look at the quality of the input, output, ripple, breakdown, temperature, certification, and other characteristics of the power supply. Apart from these, we can also judge according to the following points.
1. Circuit principle and soldering process The bare board can use intuitive methods, such as a neat layout of components and potting modules without being exposed and unable to view the internal situation. The quality of the mechanized wave soldering process is better than manual soldering, generous, but Better in terms of safety and performance
2. The core of the power supply of chip components and transformer components is IC, which will directly affect the power and high-temperature resistance of the entire power transformer components. . Responsible for accomplishing AC-DC and saturating the fryer during energy overload.
3. Is it an electrolytic capacitor or a ceramic capacitor?
1）. The electrolytic capacitor is a temperature-sensitive component after the electrolyte heats up and explodes.
2）. Ceramic capacitors are mainly non-polar, and the switching frequency will cause the parasitic resistance of the capacitor to heat up. Good dielectric materials and capacity should not be too large. Most, it is widely used in high-frequency circuits.
4. Batch testing of aging and high-temperature aging No matter how good the quality stability of product materials and production process control is and whether the materials have potential safety hazards, aging needs to be detected. Only through power aging and high-temperature pumping detection.
The benefits of choosing a China Small size power module manufacturers
Power savings of up to 25% can be achieved with these new power switches, and the reduction in power consumption brings many improvements. On the one hand, the heat dissipation design of the heat sink and the overall module can be more compact and have higher cost performance. Providing the same output power but with a smaller product is an important advantage, especially in pump or fan designs. In general, by using smaller electronic drives, controlled motors can be used in applications that were not possible before. Also, reduced use of production materials means lower costs for production, transportation, and recycling, which all boil down to product life cycle costs.
On the other hand, the maximum output power can be increased while maintaining the consistency of the existing design parameters. Products that use the same thermal design but consume less power have higher reliability, because there is a less thermal excursion, and the failure rate is greatly reduced. Moreover, the same design can evolve into a variety of different models by simply replacing different output power chips, thereby shortening the time to market.
We have more modules with different powers, if you want to know more, please contact us.
Претходно: На кои детали треба да обрнете внимание при прилагодување на модулите за напојување?
Следно: Кои се советите за избор на модул за напојување со DC/DC?
релевантни информации
-
2023-5-17
110V AC to 12V DC Converter: Converting High Voltage to Low for Efficient Power Usag
Introduction In today's world, efficient power usage has become a priority because of the scarcity of resources and the need to reduce energy consumption. One of the ways to achieve this is through the use of a converter that can change high voltage to a lower voltage that can be used by electronic devices. This article will explore the 110V AC to 12V DC converter and how it can be used to convert high voltage to low for efficient power usage. What is a 110V AC to 12V DC Converter? A 110V AC to 12V DC converter is an electronic device that can convert high voltage alternating current (AC) to low voltage direct current (DC). This device is commonly used...
Погледнете детали -
2023-5-2
Industrial AC-DC Converter for Efficient Power Conversion
Industrial AC-DC converters are devices that convert alternating current (AC) to direct current (DC) for use in industrial applications. They are designed to provide efficient power conversion, enabling industrial equipment to operate reliably and efficiently. These converters are typically used in industrial processes such as manufacturing, automation and control systems, and power distribution systems. The primary function of an AC-DC converter is to convert the voltage and frequency of incoming AC power to the appropriate DC voltage required by the equipment. This requires a complex circuitry that includes a rectifier, filter, and voltage regulator. The rectifier converts the AC voltage to DC while the filter smoothes out the output voltage, and the voltage regulator ensures the output voltage is maintained...
Погледнете детали -
2023-8-12
120V AC to 12V DC Converter manufacture: Efficient Voltage Conversion for Various Devices
Introduction: In the world of electronics, voltage conversion is a crucial process that enables devices to function optimally. One such conversion is the transformation of 120V alternating current (AC) to 12V direct current (DC). This article will discuss the importance of efficient voltage conversion and explore the benefits of a 120V AC to 12V DC converter for various devices. Understanding Voltage Conversion: Voltage conversion refers to the alteration of electrical potential between different levels. In the case of a 120V AC to 12V DC converter, the aim is to convert the high voltage alternating current commonly found in power outlets into low voltage direct current suitable for powering electronic devices. This conversion is achieved through a series of electrical components...
Погледнете детали -
2022-12-20
How to solve the problem of power module selection
It is not easy to select a power module. There are many difficulties to consider. How much do you know? Magnetic beads, capacitors, diodes, resistors... all have similar inside stories, but people don't pay much attention to them. There are various topologies of power modules, such as flyback, forward, push-pull, half-bridge, and full-bridge. Due to their different basic principles, each of them is mainly manifested in the advantages at the level of certain characteristic indicators. The flyback power supply does not have a time period for charging and discharging the battery during the power switch period. That is because there is no time characteristic of the response characteristic, and the grain baud cannot be guaranteed to be very good, although...
Погледнете детали -
2023-6-4
DC Power Conversion: Understanding the Basics and Best Practices
Power conversion is an essential process in modern electronics, enabling devices to operate using different voltage and current levels. In this article, we will take a closer look at DC power conversion, its basics, and best practices. DC power conversion refers to the process of converting DC voltage levels from one level to another. This process is necessary because different electronic devices operate using different voltage levels. For example, a smartphone may operate using a voltage of 3.7 volts, while a laptop may require a voltage of 19 volts. To ensure that electronic devices can operate efficiently and safely, DC power conversion is used to convert the voltage levels to suit the specific needs of each device. The process of...
Погледнете детали -
2023-8-16
AC/DC Power Supply Module manufacture: Ensuring Reliable and Efficient Power Conversion
Introduction In today's technology-driven world, the demand for reliable and efficient power conversion has never been higher. From small electronic devices to large industrial systems, the proper functioning of power supply modules is crucial to ensure smooth operations. One such module that has gained significant popularity is the AC/DC power supply module. This article aims to delve deeper into the functioning, benefits, and applications of this essential component. Understanding AC/DC Power Supply Module The AC/DC power supply module is a device that converts alternating current (AC) into direct current (DC), making it suitable for various electronic applications. It typically comprises a rectifier, filter, and regulator circuitry to ensure a stable output voltage and current. By converting the AC power from...
Погледнете детали